KraftMaid Kitchen Remodeling Nationwide

KraftMaid Kitchen Remodeling: The Fort Lauderdale Owner’s Guide

KraftMaid kitchen cabinet repair and replacement in Fort Lauderdale typically runs $14,000-$45,000 for a full remodel, with individual component repairs starting lower. We stock KraftMaid-compatible hardware, hinges, drawer slides, and door fronts, and we carry the most common sizes on our trucks. Most Fort Lauderdale homeowners discover their KraftMaid cabinets need attention when soft-close hinges seize in the humidity, drawer boxes sag from the weight of stored cookware, or the thermofoil finish begins peeling near the dishwasher vent where heat and moisture concentrate.

Call (754) 254-7676

Which KraftMaid Models This Applies To

KraftMaid organizes its cabinetry into several product tiers, and the replacement approach differs by line. The Canvas and Canvas 2.0 lines use a standardized 35mm cup hinge with a 110-degree opening angle, while older Vantage and Pro-Classic series from the mid-2000s used a proprietary slide-on hinge plate that KraftMaid phased out around 2014. If your cabinets predate that shift, the mounting hole pattern won’t accept current OEM hardware without a conversion bracket.

To identify your series, check the interior side of the door or the hinge cup itself for a stamped date code and model prefix. The DX prefix indicates a discontinued Vantage door style; CM or CV prefixes signal Canvas-era construction. Drawer boxes are simpler: measure the box depth. KraftMaid standardized 21-inch depth for base cabinets in 2016; earlier boxes ran 20 inches, and the slide mounting positions differ by a half-inch that matters when you’re replacing Blum or Grass hardware.

We source OEM KraftMaid hardware through authorized distribution, but for hinges and slides on discontinued lines, we spec Blum Clip-Top or Salice equivalents that meet or exceed the original cycle rating. The decision point is usually the mounting hole pattern, not the brand name on the hinge cup. We test-fit before ordering bulk to confirm the geometry holds in Fort Lauderdale’s humidity, which swells particleboard substrates differently than the dry climates where most hardware is spec’d.

Signs Your KraftMaid Kitchen Remodeling Is Failing

• Doors hang crooked or won’t stay closed. The Blum or Grass hinge has lost its internal spring tension, or the mounting screw has stripped out of the particleboard stile. In Fort Lauderdale, the combination of salt air and air conditioning cycles accelerates this; we see it most in oceanfront condos from Galt Ocean Mile to Lauderdale-by-the-Sea.
• Drawers stick, bind, or fall off the track. The roller or ball-bearing slide has corroded, or the drawer box itself has delaminated at the dovetail joint. KraftMaid’s all-ply drawer boxes hold up better than particleboard, but the slide hardware still wears; full-extension slides under a loaded pot drawer typically show failure around year 8 in this climate.
• Thermofoil or laminate surfaces bubble, peel, or discolor. Heat from self-cleaning oven cycles, dishwasher vents, or unvented range hoods degrades the adhesive. The damage is cosmetic but progressive; once the substrate swells, the door won’t plane properly and the hinge geometry shifts.
• Corner base cabinets develop a musty odor or soft floor. The sink cabinet toe-kick or lazy Susan base has taken water from a slow plumbing leak. KraftMaid’s standard melamine interior resists surface mold but won’t stop rot in the floor panel if water pools undetected.
• Wall cabinets feel loose or pull away from studs. The mounting rail system or ledger board has failed, often because original installers missed studs or used inadequate fasteners. This is a safety issue; a loaded wall cabinet can weigh 150 pounds or more.

Before

After

Replacement Cost & What’s Included

Component-level KraftMaid repair in Fort Lauderdale starts around $400 for hinge and adjustment work on a run of base cabinets, and runs to $2,500-$6,500 for drawer box and slide replacement throughout a medium kitchen. Full cabinet replacement with new KraftMaid boxes, doors, and hardware falls in the $14,000-$45,000 range depending on layout complexity, finish grade, and whether we reconfigure the footprint.

Our quotes itemize: material by line item (hinge count, door square footage, box linear feet), labor by phase (demolition, install, adjustment), and a separate line for disposal. Under Clause 1 of the Haven Standard, that written price is fixed; no change proceeds without a signed change order. The 365-Day Done Right Promise covers both parts and labor, and every visit includes a documented photo record of before, during, and after conditions.

DIY or Call Us?

A homeowner can safely check hinge adjustment screws with a Phillips driver and confirm whether the issue is alignment or hardware failure. If the hinge cup is cracked or the slide carriage is bent, replacement requires more: removing the door or drawer without damaging the finish, drilling new mounting holes if the particleboard has stripped, and setting the reveal gaps to KraftMaid’s 1/8-inch standard. Wall cabinet mounting and any electrical or plumbing adjacent to cabinet work should involve a licensed professional; the fastener and stud specification isn’t intuitive, and a falling wall cabinet is a genuine hazard.

We carry Blum, Salice, and Grass hardware on our Fort Lauderdale trucks, plus the conversion brackets for discontinued KraftMaid hinge patterns. If you’re matching a finish or a door profile that’s been discontinued, we can cross-reference to current KraftMaid equivalents or source from our secondary relationships with Wellborn and other vetted brands. Call (754) 254-7676 to schedule your free estimate; we’ll bring samples and measure on-site.

FAQs