Boral Windows & Doors Nationwide

Boral Windows & Doors: The Fort Lauderdale Owner’s Guide

We stock and install Boral-compatible windows and doors across Fort Lauderdale, with most replacement projects quoted in the $4,500-$15,000 range for window replacement and $8,000-$25,000 for full impact window installation depending on opening count and series. Boral parts are available same-day for common failures, and we carry the full line of Boral hardware, weatherstripping, and sash components on our Fort Lauderdale trucks. Most owners discover a problem when the sash won’t stay open, they feel salt-air draft around the frame, or they spot corrosion on the coastal-grade hardware after a humid summer.

Call (754) 254-7676

Which Boral Models This Applies To

Boral’s window and door catalog spans several series, and the part you need depends on the vintage and line. Current Fort Lauderdale installations we service most often include the Boral 3000 Series vinyl windows, the Boral 5000 Series aluminum-clad line, and the Boral Coastal impact-rated products designed for Florida’s HVHZ (High Velocity Hurricane Zone) requirements. The model number is stamped on the hinge side of the frame or on a label between the glass panes on insulated units; it’s a 6- to 10-digit code starting with the series prefix.

Here’s where owners get tripped up: Boral changed its locking hardware geometry between the 2016 and 2019 production runs. The pre-2019 mortise lock uses a 45-degree cam slot; post-2019 switched to 30-degree. An OEM replacement ordered by sight will bind or fail to engage. We measure the cam angle and backset on every Fort Lauderdale service call because we’ve seen the wrong part installed by well-meaning homeowners three times in Victoria Park alone. For weatherstripping and sash balances, quality aftermarket equivalents from Amesbury and Caldwell meet Boral’s original specs at lower cost; for locks and hinges in impact-rated units, we recommend OEM to maintain the HVHZ certification documentation your insurer may request.

Signs Your Boral Windows & Doors Is Failing

• Sash drops or won’t stay open. The coil balance system has lost tension, usually from corrosion in the Florida humidity. Boral’s constant-force balances are rated for 10,000 cycles but salt air accelerates wear; we replace with stainless-steel hardware in Fort Lauderdale jobs.
• Visible daylight or air movement around the frame. Compression weatherstripping has flattened or the pile seal has detached from the track. In coastal Fort Lauderdale, UV degradation hits the exposed face of the seal while the interior side looks fine; partial replacement leaves the leak.
• Lock lever turns but doesn’t engage the keeper. The mortise lock cam has worn or the keeper screw holes have stripped out of the aluminum frame. This is the 45-degree versus 30-degree compatibility issue; forcing the lever will snap the cam.
• Condensation between glass panes. The insulated glass unit (IGU) seal has failed, allowing moist Fort Lauderdale air into the airspace. The glass pack needs replacement, not the whole window; we measure the daylight opening and order a custom IGU with matching Low-E coating.
• Corrosion pitting on exterior hardware. Boral’s coastal-grade hardware is anodized aluminum, but the screw fasteners are often standard zinc-plated steel. The screws fail first, and the hardware loosens; we upgrade to 316 stainless fasteners on every Fort Lauderdale replacement.

Before

After

Replacement Cost & What’s Included

The range depends on three factors: whether the part is in our Fort Lauderdale stock or needs ordering, whether the frame substrate is intact (stucco or wood rot around the opening adds repair scope), and whether the unit is impact-rated (HVHZ hardware costs more but is legally required for most Fort Lauderdale addresses east of Federal Highway). Every quote is flat and written before work starts, with parts and labor itemized separately. Under our 365-Day Done Right Promise, if the new part doesn’t perform as specified, we replace it at no charge. The Haven Standard requires that signature.

DIY or Call Us?

There’s a safe middle ground for Boral owners. You can check the model label, photograph the failed part, and verify whether the lock engages smoothly with the window open (no pressure on the frame). What you should not do: remove a sash with a coil balance under tension, attempt to cut or drill impact-rated glass, or force a lock that isn’t engaging. The balance spring stores significant energy and can recoil unpredictably; impact glass is laminated and will spider-crack if the edge is compromised. We’ve been called to Fort Lauderdale homes where a DIY balance replacement scratched the frame or where a homeowner cracked an IGU trying to “reseal” it with caulk. Measure twice, write it down, then say it once - that’s how we scope every job. If the part involves tension, glass, or the HVHZ certification, call us at (754) 254-7676 and we’ll quote it flat, in writing, before anyone picks up a tool.

FAQs