Oldcastle Fence Installation Nationwide

Oldcastle Fence Installation: The Fort Lauderdale Owner’s Guide

Oldcastle fence installation in Fort Lauderdale typically runs $3,500-$9,000 for a complete vinyl or aluminum system, with most residential jobs quoted in writing within 24 hours and crews available to start within a few days of approval. We stock Oldcastle-compatible posts, panels, and hardware for common series, and we carry KraftMaid, Cambria, and Silestone for related exterior projects. Most Fort Lauderdale homeowners discover their Oldcastle fence is failing when posts lean after a tropical storm, gates sag and won’t latch, or pickets crack where the afternoon sun hits hardest - usually after 8-12 years in our salt-air climate.

Call (754) 254-7676

Which Oldcastle Models This Applies To

Oldcastle fence systems span multiple product lines, and the part you need depends on when it was installed and which series was specified. The Oldcastle Coastal series, common in South Florida subdivisions built 2012-2019, uses 5-inch square vinyl posts with routed holes for 7/8-inch pickets - a profile that looks standard but isn’t interchangeable with newer 6-inch post designs. Oldcastle Savannah aluminum fencing, popular for pool enclosures in Fort Lauderdale’s Victoria Park and Coral Ridge neighborhoods, uses 1.5-inch rail sections with proprietary bracket spacing at 6 feet on center. Check the post cap for an embossed series name, or measure the post width and rail height before ordering anything.

We source OEM Oldcastle components where they’re still manufactured, but we’ve also vetted aftermarket equivalents from Fortress and Ameristar that match the gauge, wall thickness, and UV stabilizer specs - and we list both options in our written quotes, with the compatibility notes that let you decide. The aftermarket rails we use carry the same 20-year structural warranty as OEM, which matters in Fort Lauderdale where the salt index at the coast accelerates corrosion on anything below 0.040-inch aluminum wall thickness. If your fence was installed by a previous owner without documentation, we’ll measure on-site and cross-reference the post profile against Oldcastle’s archived spec sheets - part of the photo record we deliver after every visit.

Signs Your Oldcastle Fence Installation Is Failing

• Posts lean or wobble at the base. In Fort Lauderdale’s sandy loam soil, especially east of Federal Highway where the water table sits higher, Oldcastle posts set without proper concrete footing depth (30 inches minimum for 6-foot fence height) loosen after repeated wet-dry cycles. The post itself may be sound, but the footing has eroded or the concrete collar has cracked from root intrusion.
• Gate sags and the latch misses the strike plate. Oldcastle gates rely on a diagonal tension brace inside the frame; when the fasteners corrode - common within 7 years if standard zinc hardware was used instead of stainless - the rectangle becomes a parallelogram. The gate doesn’t just look off; the latch mechanism takes stress and the jamb post starts to twist.
• Pickets crack, chalk, or discolor in bands. UV degradation hits the south and west faces first in Fort Lauderdale’s exposure. Oldcastle vinyl with insufficient titanium dioxide loading (earlier production runs, roughly pre-2015) turns brittle and snaps at the routed hole, where stress concentrates. Chalking is cosmetic; cracking means structural replacement.
• Rails pull from posts at the bracket. Thermal expansion in Florida’s 90-degree daily swings stresses the rail-to-post connection. Oldcastle’s snap-lock brackets can fatigue after repeated cycles, especially on dark-colored aluminum that runs 40°F hotter than ambient. The rail separates enough for pickets to fall out.
• Corrosion blooms at post base or gate hinges. Salt spray from Atlantic breezes, even three miles inland, attacks any bare aluminum or steel. Oldcastle aluminum fence with factory powder coat in good condition resists this; scratches from lawn equipment or pet damage expose raw metal, and the corrosion spreads under the coating in a filiform pattern that looks like worm tracks.

Before

After

Replacement Cost & What’s Included

The spread depends on three things we itemize in every quote: linear footage, access for our auger (tight lots in Victoria Park or Las Olas Isles take longer), and whether we hit coral rock that requires pneumatic breaking. Our price is flat - parts, labor, disposal, permit pull if required by your Fort Lauderdale zone - with no change order unless you add scope and sign for it. Under Clause 1 of The Haven Standard, that written number is fixed before anyone digs. We also offer a Free Second Opinion on any competitor’s written estimate; bring it in and we’ll review it line by line.

DIY or Call Us?

There’s a short list of checks any owner can make safely. Confirm the gate latch is clear of debris. Verify the post isn’t loose by applying steady pressure with your shoulder - don’t kick or ram it. Look for visible cracks in vinyl or powder coat failure on aluminum. That’s about where safe DIY ends.

What goes wrong past that point: digging near unmarked utilities in Fort Lauderdale’s dense utility corridors, setting posts out of plumb so the gate won’t ever hang right, using standard fasteners that’ll corrode within two years in our salt air, or pouring footings too shallow and watching the fence lean after the first tropical downpour. Post-setting is straightforward until it isn’t, and a leaning fence is a code violation that complicates your home sale. We’re not affiliated with Oldcastle - we’re independent installers who’ve worked with their systems enough to know where the tolerances tighten. Call (754) 254-7676 for a written estimate; the visit and quote are free, and you’ll leave with a photo record of what we found.

FAQs