Jerith Fence Installation Nationwide

Jerith Fence Installation: The Fort Lauderdale Owner’s Guide

Jerith aluminum fence installation in Fort Lauderdale typically runs $3,500-$9,000 for a complete residential system, with most standard lots falling in the $4,500-$6,500 range depending on linear footage and series height. We stock Jerith-compatible posts, rails, and hardware for same-day repair on common failures, and we carry the full catalog for new installs across the I-Series, Ovation, and Style-Craft lines. Most Fort Lauderdale owners first notice trouble when a gate sags against the striker plate, a post leans after a tropical storm, or pickets rattle loose where the hidden fasteners have backed out in the salt air.

Call (754) 254-7676

Which Jerith Models This Applies To

Jerith builds three residential series that dominate the Fort Lauderdale market, and the parts are not interchangeable between them. The I-Series uses a 1-inch square rail with a .062 wall thickness and a bracket-mounted post system; the Ovation steps up to a 1.5-inch rail with a heavier .080 wall and a routed post design that hides the rail ends entirely. Style-Craft splits the difference at 1.25-inch rails and offers the most ornamental picket profiles, including the pressed-spear and triad tops common in Victoria Park and Coral Ridge.

To identify your series, check the inside face of the gate frame for a stamped date code and series mark, or measure the rail outer diameter with a tape measure. The post wall thickness matters for replacement: I-Series posts are .100, Ovation posts are .125, and forcing an Ovation rail into an I-Series post will split the wall or leave the bracket loose. We source OEM Jerith components through their East Coast distributor, though for posts damaged by ground contact we often spec a heavier-gauge marine-grade equivalent with a 20-year finish warranty that matches Jerith’s AAMA 2604 spec. Rowan Construction Group Fort Lauderdale is an independent service provider, not affiliated with Jerith.

Signs Your Jerith Fence Installation Is Failing

• Gate drags or won’t latch. The most common call we get in Fort Lauderdale. The cause is usually hinge pin elongation in the J-bolt assembly, where the zinc coating has worn through and the salt air has started pitting the stainless pin. Left alone, the gate frame itself twists.
• Post leans at the base. In the sandy soils east of Federal Highway, posts settle or the concrete footing fractures from root pressure or storm surge. Jerith posts are hollow aluminum, so they don’t rot, but they will kink if the footing shifts more than 2 degrees.
• Picket rattle in the wind. The hidden fastener system uses a nylon snap-in clip that UV-degrades after 8-12 years in South Florida sun. Once the clip loses tension, the picket taps against the rail and the finish wears through at the contact point.
• Rail bows between posts. This happens when the original installer spaced posts beyond the 72-inch maximum for I-Series or 96-inch for Ovation, or when a vehicle bumper has clipped the rail and stressed the bracket. The rail itself rarely fails; the bracket tears out of the post.
• Finish chalks or pits. Jerith’s powder coat is rated for 20 years, but within a mile of the Intracoastal the salt load accelerates fade on south-facing runs. Chalking is cosmetic; pitting means the substrate is exposed and will bloom with white corrosion within two seasons.

Before

After

Replacement Cost & What’s Included

The range on a full install reflects three variables: series selection (Ovation runs 20-30% more than I-Series), site conditions (rock excavation or tight access between houses in Rio Vista adds labor), and gate count (a dual-drive auto-gate with Jerith’s ornamental scrollwork can add $1,800-$2,400). Our quotes itemize material by lineal foot, hardware by piece, and labor by phase: layout, dig, set, hang, and final adjustment. Under Clause 1 of the Haven Standard, that written price is delivered before any work starts. The 365-Day Done Right Promise covers installation defects; manufacturer finish warranties pass through directly from Jerith or our marine-grade equivalent supplier.

DIY or Call Us?

There’s no high-tension danger in aluminum fence work, but there are two places where DIY goes wrong fast. Post setting looks simple until you’ve dug three holes in Fort Lauderdale’s marl and shell layers and realize your 4-foot depth is 6 inches short of stable bearing. And gate alignment is unforgiving: a 1/8-inch hinge pin offset compounds to a 3/4-inch latch miss at the striker, and the adjustment has to happen with the gate under its own weight.

What you can safely check: verify the series mark on your rail, photograph any part numbers, and confirm whether the failure is in the component or the installation (loose concrete, over-spanned rails). What we handle: footing excavation to 42-inch depth minimum, laser-leveled post plumb, and gate swing geometry adjusted with shims, not force. Measure twice, write it down, then say it once. Call (754) 254-7676 and we’ll scope it in person, with a written price before any work starts.

FAQs