Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Before
After
Before
After
Before
AfterWellborn Roofing: The Fort Lauderdale Owner’s Guide
We stock and install Wellborn-compatible roofing components in Fort Lauderdale, with most replacement parts available same-day and installed pricing typically running $400-$1,800 depending on the component and roof access. Wellborn roofing systems, common on homes built in Broward County between the late 1990s and mid-2010s, use proprietary flashing profiles and fastener spacing that don’t always interchange with generic equivalents. Most Fort Lauderdale homeowners discover a part has failed after a hard rain - water staining on the ceiling, granules in the gutter, or a visible gap where the soffit meets the roofline in neighborhoods like Victoria Park, where mature oak canopies make ladder work tricky and delay detection.
Which Wellborn Models This Applies To
Wellborn produced three residential roofing product lines relevant to Fort Lauderdale homes: the Classic Series (1998-2008), Pro-Grade Series (2005-2015), and the limited-run Coastal Shield line (2010-2014) developed specifically for high-humidity, salt-air environments. The Classic Series used 5-inch K-style aluminum gutters with 2×3 downspouts and proprietary hidden hangers spaced 24 inches on center - closer than the industry-standard 32 inches, which is why generic hangers often sag within a season. The Pro-Grade switched to 6-inch gutters with 3×4 downspouts and a wider 5.5-inch fascia flashing profile that overlaps differently than standard 4-inch flashing.
To identify your series, check the inside face of the gutter for an embossed “WB” stamp followed by a two-digit year code. The Coastal Shield line carries a small salt-spray icon near the downspout outlet. We carry OEM-compatible hangers, end caps, and outlet tubes for all three lines, plus aftermarket alternatives from Spectra Metals and Berger that meet the same .032-gauge aluminum spec at roughly 15% less cost. The catch: Coastal Shield’s modified corner miters use a 37-degree cut rather than standard 45 degrees, so aftermarket corners won’t seal without field modification. We note the exact series on every written quote so there’s no mismatch.
Rowan Construction Group Fort Lauderdale is an independent service provider, not affiliated with Wellborn.
Signs Your Wellborn Roofing Is Failing
- Gutter pulling away from fascia. Wellborn’s hidden hanger system relies on a 1.5-inch fascia screw bite; in Fort Lauderdale’s humidity cycle, the fascia board swells and compresses, loosening the grip. You’ll see a visible gap between gutter back and fascia, often worst on the south-facing eave where thermal expansion is highest.
- Water marks on exterior walls below the roofline. This usually traces to failed end-cap seals or separated downspout elbows. Wellborn’s original end caps used a butyl sealant that hardens after 8-12 years of UV exposure; the gap opens slowly, so staining appears before any interior damage.
- Granule accumulation at downspout outlets. Normal shingle shedding collects here, but excessive buildup means water is backing up in the gutter. On Wellborn systems, the outlet tube has a slightly narrower throat than standard - 2.25 inches versus 2.5 - so debris compacts faster.
- Visible rust streaks on white or light-colored gutters. Wellborn’s aluminum shouldn’t rust; streaks indicate galvanic corrosion where a steel fastener or incompatible hanger was substituted in a previous repair. The corrosion spreads from the contact point outward.
- Soffit vent screens clogged with shingle grit. In Fort Lauderdale’s afternoon thunderstorms, wind-driven rain enters through the soffit if the drip edge flashing has lifted. Wellborn’s drip edge on the Classic Series used a shorter 2-inch leg than current code requires; it simply doesn’t reach far enough in wind-driven conditions.
Before
AfterReplacement Cost & What’s Included
For Fort Lauderdale homeowners, Wellborn roofing component replacement runs $400-$1,800 installed, with most single-component jobs falling in the $600-$950 range. Here’s how the price breaks:
- Gutter hanger replacement (per linear foot, including fascia repair if needed): $8-$14
- End cap or outlet tube replacement: $180-$340
- Downspout elbow or extension swap: $220-$420
- Drip edge flashing replacement (per linear foot): $12-$18
- Full gutter section replacement (20 linear feet, Pro-Grade): $1,200-$1,800
The range reflects three variables: roof height (single-story versus two-story with pool cage interference), fascia condition (softened wood requires sistering or replacement before new hangers hold), and whether we’re matching existing color or switching to a current stock color. Every quote lists the part by name, the gauge and finish spec, and the labor line separate - no bundled “gutter package” that hides what’s actually being done. Under Clause 1 of the Haven Standard, that written price is fixed; if we find softened fascia during removal, we document it with photos, write a change order with the exact additional cost, and nothing proceeds until it’s signed. Our workmanship on roofing components carries the 365-Day Done Right Promise.
DIY or Call Us?
There’s a safe middle ground here. A homeowner can walk the perimeter after rain, note which gutter sections hold standing water, and photograph any gaps or stains - that documentation helps us quote accurately without a ladder set. You can also clear downspout outlets by hand or with a garden hose, provided the roof edge is dry and you’re working from ground level with an extension tool.
Where DIY goes wrong: ladder work on Fort Lauderdale’s older homes, especially in neighborhoods like Victoria Park with uneven ground and mature root systems that shift patio pavers beneath the ladder feet. The fascia behind Wellborn gutters is often original 1x pine that’s softened from decades of humidity; a ladder stabilizer pressing into compromised wood can punch through, and a fall from even 10 feet carries serious injury risk. Hanger spacing matters too - we’ve seen well-meaning homeowners install standard 32-inch hangers on Wellborn’s 24-inch centers, creating a wave pattern that pools water and voids any warranty discussion. If you’re not certain of the series, the gauge, or the fascia condition behind the gutter, call (754) 254-7676 and we’ll scope it with a written price before any work starts.
FAQs
In Fort Lauderdale’s climate, expect 12-18 years for Classic Series gutters and hangers, 15-22 years for Pro-Grade, and 18-25 years for Coastal Shield components. The limiting factor is usually the sealant and fastener corrosion, not the aluminum itself. Salt air within two miles of the Intracoastal shortens that by roughly 20%; inland neighborhoods like Coral Ridge see the longer end of the range. Call (754) 254-7676 for an exact condition check - estimates are free.
Sometimes. A single loose hanger can be re-secured if the fascia is sound and the original hanger bracket isn’t cracked. End-cap sealant can be cut out and re-bedded if the cap itself isn’t warped. But once aluminum develops pinhole corrosion or a gutter section has sagged enough to hold standing water, replacement is the only fix that lasts. We photograph the condition and show you both options with prices for each. Call (754) 254-7676 to schedule.
Most single-component replacements - an end cap, outlet tube, or section of hangers - take 2-3 hours on site. A full 20-linear-foot gutter run runs 4-6 hours including removal, fascia inspection, and proper pitch reset. We don’t quote in “gutter lengths per day”; we quote the actual hours and crew size your job requires, then hit that number. Call (754) 254-7676 for a written time estimate with your price.
We stock hangers, end caps, outlet tubes, and downspout fittings for all three Wellborn series on every Fort Lauderdale service vehicle, plus color-matched touch-up paint for the most common white, clay, and bronze finishes. Full gutter sections and custom-order colors arrive next business day from our Davie supplier. If we don’t have it, we don’t guess - we tell you the lead time in writing before you commit. Call (754) 254-7676 to confirm availability for your specific model.
We also stock parts for KraftMaid, Cambria, and Silestone products.
Measure twice, write it down, then say it once. That’s how we scope every job, whether it’s a single hanger or a full roof replacement in Fort Lauderdale.
Ready to get the exact part matched, priced, and scheduled? Call Rowan Construction Group Fort Lauderdale at (754) 254-7676. We’ll confirm your Wellborn series, deliver a written line-item quote, and book the work - no deposit required, no price changes without a signed change order, and a documented photo record included as standard.
Written by Grant Rowan, Owner, Rowan Construction Group - Fort Lauderdale, FL at Rowan Construction Group Fort Lauderdale, serving Fort Lauderdale and nearby areas.